- TEAM
MMSMC
ROBBINS
- SERVICES
TBM’s Tunnel Boring Machines
- CATEGORY
TBM’s Machines
Nepal has been digging tunnels using the conventional drill and blast since 1950s. The D&B method is a standard method to dig tunnels not only in Nepal but worldwide. However, in the recent past the use of mechanized tunneling methods using Tunnel Boring Machine (TBMs) are becoming increasingly popular methods to dig tunnels of longer lengths. Nepal used its first TBM in 2015 to dig the tunnel for Bheri Babai Diversion Multipurpose Project. The TBM manufactured by Robbins-A global TBM Company and supplied through MMSM to the contractor appointed by Department of irrigation (DoI), Nepal was successful in completing the tunnel boring of 12.3 KMs of tunnel in just 17 months. This could have taken more than 10 years if dug through Drill & Blast method.
Similarly, the second TBM project in Nepal Sunkoshi Marine Diversion Multipurpose Project under the same department opted to dig its 13.3 KM tunnel using the TBM manufactured and redesigned by Robbins. The tunnel was completed in 19 months about 7 months ahead of schedule.
These successes have proven the worth of TBM’s in Nepal. Now more and more contractors and Developers are exploring the option of using TBMs for their tunnels. The initial capital investment in this method creates a doubt among the tunneler, however it has been seen globally and in Nepal that the significant time saved by using the machine, completely justifies the initial investment. Any tunnels longer than 7km is worth digging using a Tunnel Boring machine.
TBM offerings
3. Tunnel Boring Machines
If the geology of your tunnel ranges from soft soils to weathered rock, then a Robbins Earth Pressure Balance Machine (EPBM) is the correct technical solution for your project. This is particularly true when your project is located in an urban environment and ground surface subsidence cannot be tolerated.
EPBMs are utilized in the construction of rail tunnels, metropolitan subway systems, highway tunnels, and other projects where the tunnel will be constructed either partly or completely in soft soil beneath the water table.
Robbins has integrated over 50 years of TBM design and jobsite experience into our EPBMs. Nobody has a wider range of experience designing innovative machinery to cope with difficult underground conditions. Our engineers will tailor your EPBM to handle the specific challenges of your project. From “Smooth Flow” cutterheads that reduce friction to super-reliable back-filling systems and Variable Frequency Cutterhead Drives, Robbins has taken the traditional EPB design to the next level.
What is an Earth Pressure Balance Machine?
Earth Pressure Balance Machines (EPBMs) are shield machines specially designed for operation in soft ground conditions containing water under pressure. Loose sedimentary deposits with large boulders and a high water table will challenge ordinary TBMs, but not Robbins EPBMs. Robbins EPBMs have an articulated shield that is sealed against the pressure of water inflows up to 10 Bar. Robbins EPBMs control the stability of the tunnel face and subsidence of the ground surface by monitoring and adjusting the pressure inside the cutterhead chamber to achieve a balance with the pressure in front of the cutterhead, hence the name “Earth Pressure Balance.”
The working area inside the EPBM is completely sealed against the fluid pressure of the ground outside the machine.
A screw conveyor removes the fluidized muck behind the cutterhead and in front of the pressure bulkhead. The screw conveyor’s speed and discharge rate is controlled by the operator and is used to control the pressure at the working face and to match the muck discharge rate to the advance rate of the EPBM.
The articulated joint between the forward shield and tail shield is equipped with a high pressure seal that allows angular movement between the shields and prevents water from seeping into the interior of the EPBM.
The EPBM erects the segmented tunnel lining sequentially after each push. Specially designed high pressure seals in the tail shield effectively seal the machine to the outside of the tunnel lining and create a barrier against ground pressure.
When it becomes necessary to enter the cutterhead chamber to inspect the cutterhead or change cutting tools, the workers can safely enter through a manlock while compressed air is used to maintain earth pressure balance to support the working face.
EPBMs can be steered through incredibly small turn radii when necessary by employing the articulation joint and the copy cutter mounted in the cutterhead. Robbins engineers will calculate the correct amount of copy cutter extension and the articulation angle required for the particular radius requirements of a given tunnel.
“The design of the machine, cutterhead, and cutter setup from Robbins shows, after the left line breakthrough at 1,400 m, the wear of the disc cutters was only 4.1 mm, and therefore cutter replacement was unnecessary before it started on the right line tunnel.”
– Li Quan She, Project Manager, CRCC 23rd Bureau, Chengdu Metro Project Line 2
ALL ROBBINS EPBMs ARE EQUIPPED WITH:
- A cutterhead and cutting tools specifically engineered to cope with the expected geology. The cutterhead may be designed with:
- Robbins back-loading disc cutters and drag picks where soil with boulders or massive rock is expected.
- Drag picks only where no rock is expected.
- Full coverage with drag picks and partial coverage with disc cutters where occasional boulders are expected.
- A copy cutter to overcut the tunnel for steering.
- A durable cutterhead with the largest opening capacity in the industry, driven by a proven VFD system.
- A “Smooth Flow” design that reduces cutterhead friction.
- A high capacity main bearing for reliability and longevity.
- High-pressure seals on the cutterhead drive, articulation joint and tail shield to prevent water inflow.
- High-speed rotary segment erector mounted in the tail shield for perfect alignment with the segments.
- Thrust cylinders mounted in the tail shield for correct alignment with the segments.
- Active shield articulation cylinders for steering and transfer of thrust from the tail shield to the forward shield.
- Digital guidance system with continuous display of actual tunnel alignment vs. the design alignment and information for accurately building segment rings.
Robbins designs EPBMs to meet the criteria of each specific project, including the geologic conditions, tunnel design, construction plan, project schedule, site logistics and many other factors. When you contact Robbins, we review your project specifications to determine the best machine for your project. In some cases, an entirely new tunnel boring machine will be the answer. On other projects, the best decision may be to refurbish an existing TBM, to save you time and money.